Every irrigation line starts with a solenoid valve. The signal that opens it comes from the controller. Where the controller sits and where it gets its power decide the installation cost. How the valve itself works: what is a solenoid valve and how does it work in irrigation?

Irrigation controller types

TypePowerProgrammingRemote controlWhere it fits
Stand-alone timerMains or batteryOn site, at the deviceNoneSmall area with one valve
Wired central cabinetMains and transformerAt the cabinetIf the cabinet is networkedOne large area
Battery Bluetooth unit (ESTRON BLE)2 × 9 V batteriesFrom a phone, 10 mNone; no internet neededSmall sites, maintenance crews
Battery LoRaWAN unit (ESTRON BLE-LoRa)2 × 9 V batteriesFrom a phone and from the officeYes; needs a gatewayParks, medians, many valves
NB-IoT unit (ESTRON BLE-NB-IoT)2 × 9 V batteriesFrom a phone and from the officeYes; cellular networkPoints where no gateway can be installed

Stand-alone timer

The simplest type. It opens the valve at a set time and closes it when the duration ends. The schedule is entered on site. It ignores the weather and waters in the rain. When the season changes, every device is adjusted one by one.

Wired central cabinet

Valves are wired to a cabinet. The cabinet needs mains power and a transformer. A cable runs to every valve. It works well in one large area. Across hundreds of small areas spread over a city, cables and digging are not practical. Side by side: three methods of central irrigation control.

Battery Bluetooth unit

The unit sits in the valve box, next to the solenoid. It runs on 2 × 9 V batteries. No cable is laid. The schedule is uploaded from a phone over Bluetooth, within 10 m of the valve. No internet is needed. It suits small sites and maintenance crews.

Battery LoRaWAN unit

LoRaWAN is added to Bluetooth. Valves are managed from the office through the web panel. Range is up to 2 km in the city and 10 km in open terrain. One gateway on site is required. The AI decision reaches the unit directly. Recommended for parks, road medians and sites with many valves. What the gateway does: what is a LoRaWAN gateway and how is it installed?

NB-IoT unit

An NB-IoT cellular link is added to Bluetooth. The operator's network takes the place of a gateway.

ESTRON LND-1 / LND-2 battery irrigation controller: LoRaWAN and Bluetooth marks on the lid

Battery irrigation controller: LND-1 and LND-2

ESTRON's battery units come in two models. LND-1 has one output; it manages one valve. It has a pulse input; a flow sensor or water meter connects there. Leak detection works through this input. LND-2 has two outputs; it manages two valves with separate schedules. It has no pulse input.

Both models run on 2 × 9 V batteries. The housing is rated IP67 and measures 135 × 84 × 70 mm. The schedule is stored in internal memory; irrigation does not stop when the connection drops. The unit is password protected; a stolen unit cannot be used elsewhere. It works with DC latching solenoids; the coil type is checked at the site survey. Details: battery LoRaWAN valve controller. The other parts of the system: system components.

Which irrigation controller should you choose?

Five questions settle the choice.

  1. Is there power in the valve box? Usually not. Without power, a battery unit is the only option. Battery life depends on reporting frequency; with infrequent reporting it lasts for years. Details: low power consumption.
  2. How many valves, and how scattered? In a small area with one valve, a timer or ESTRON BLE is enough. With dozens of valves along a road, a LoRaWAN unit and one gateway are needed.
  3. Is remote control required? To change a schedule from the office or open a valve without a site visit, choose the LoRaWAN or NB-IoT version.
  4. Is leak detection wanted? A flow sensor connects to the pulse input of LND-1. Flow while the valve is closed raises an alarm. Choose LND-1 on those lines.
  5. What happens when the internet is down? A battery unit keeps the schedule in memory. It runs on time without a connection. Details: irrigation keeps running without internet.

A staged approach is possible. The BLE and BLE-LoRa versions share the same housing. ESTRON is made in Türkiye; hardware and software are developed locally.

In short: a timer looks at the clock; a cabinet wants cables. A battery unit sits in the valve box; no cable. The Bluetooth version is managed on site, the LoRaWAN version from the office. No power: battery. Many valves: LoRaWAN. Leak detection: LND-1.

Frequently asked

How many valves does a battery irrigation controller manage?

LND-1 manages one valve and LND-2 two. Two valves in the same box connect to one LND-2. A third valve needs a second unit.

Do the pipes change when moving from a timer to a battery unit?

No. Pipes, sprinklers and the solenoid valve stay. The unit is fitted in the valve box, next to the solenoid. No digging and no cable ducts.

Which type costs less?

The cost is set by the number of valves, the version and the number of gateways. Since the existing valve is kept, there is no infrastructure item. Details: smart irrigation system cost. Other questions are on the FAQ page.