A plant loses water in two ways: evaporation from the soil surface and transpiration from the leaves. Their sum is evapotranspiration, measured in millimetres. 1 mm means 1 litre per square metre. The loss rises on a hot, dry and windy day and falls on a cool, humid day.

Three terms: ET0, Kc and ETc

FAO-56 is the irrigation and drainage paper of the United Nations Food and Agriculture Organization. It is the common method worldwide. It uses three terms:

  • ET0, reference evapotranspiration. The water loss of a hypothetical reference surface: a well-watered, actively growing grass 0.12 m tall, with a surface resistance of 70 s/m and an albedo of 0.23. ET0 depends only on the weather, not on the plant.
  • Kc, the crop coefficient. The ratio of the actual plant to the reference grass. It depends on the species and the growth stage.
  • ETc, crop evapotranspiration. The product of the two: ETc = Kc × ET0.

How is ET0 calculated? FAO-56 Penman-Monteith

FAO-56 recommends a single standard equation, Penman-Monteith:

ET0 = [0.408 Δ (Rn − G) + γ · 900 / (T + 273) · u2 (es − ea)] / [Δ + γ (1 + 0.34 u2)]

Rn is net radiation and G the soil heat flux (MJ/m²/day; G ≈ 0 for daily steps). T is the mean daily air temperature at 2 m (°C), u2 the wind speed at 2 m (m/s). es − ea is the vapour pressure deficit (kPa): how dry the air is. Δ is the slope of the vapour pressure curve, γ the psychrometric constant (kPa/°C). The factor 0.408 converts energy to millimetres.

The inputs are daily maximum and minimum temperature, relative humidity, wind speed and sunshine hours. When humidity or radiation data are missing, FAO-56 gives ways to estimate them from temperature. With temperature only, the Hargreaves equation is a less accurate fallback.

Kc: coefficients for turf and landscapes

Table 12 of FAO-56 gives three values for turf grass: initial, mid-season and late season.

CropKc initialKc midKc end
Cool-season turf grass0.900.950.95
Warm-season turf grass0.800.850.85

Turf is close to the reference surface, so its coefficient is close to 1. FAO-56 gives no single value for trees, shrubs and ground covers; in a mixed landscape the coefficient depends on species, density and microclimate and is usually lower. That is why lawn, shrubs and new plantings belong on separate lines, each with its own coefficient.

From ETc to the water budget

ETc states the demand; irrigation does not supply all of it. Rain from the last 24 hours is subtracted. Part of a light shower evaporates, so "effective rainfall" is used. Water left in the soil from yesterday is subtracted too:

Water to apply (mm) = ETc − effective rainfall − water left in the soil

The root zone works like a reservoir. FAO-56 sets a threshold for it: water before the level drops below the threshold, and do not overfill. Excess water drains below the roots and is lost.

Example: ET0 6 mm, mid-season cool-season turf, Kc 0.95. ETc = 0.95 × 6 = 5.7 mm. No rain, no carry-over: 100 m² of lawn receives 570 litres. Minutes follow from the line's flow rate: duration (min) = water (mm) × area (m²) ÷ flow (L/min), plus a 10–25% allowance for sprinklers. Worked example: how to calculate lawn watering time.

Same line, three days: an example water budget

Day (example)ET0KcETcEffective rainWater to apply
Cool spring day2.5 mm0.902.3 mm3 mm0 — no watering
Hot summer day7 mm0.956.7 mm06.7 mm
Mild autumn day4 mm0.953.8 mm1 mm2.8 mm

The values are examples. Three days, three durations. A fixed "30 minutes every day" schedule wastes water on the first day and gives too little on the second.

In the cloud, the AI calculates the daily water demand and sets the irrigation duration

How does ESTRON run this calculation?

The system runs these steps every morning, for every line. ET0 comes from the hourly weather forecast. ETc is calculated with FAO-56. Rain from the last 24 hours and the previous watering are subtracted. The result is compared with the line's reference duration and comes out as a percentage: 70% of normal, for example. You enter the reference duration once.

The percentage is not applied on its own. Plant health (NDVI) and soil moisture from satellite data join the picture. Wind limit, frost risk and rain probability are observed, and your rules apply: "Postpone if wind exceeds 6 m/s." Every decision is logged with its reason. Decision steps: how does the AI make the irrigation decision? Weather data: weather-based irrigation.

On a line with a flow sensor the loop is closed: the water given is measured in litres and compared with the expected amount. The result, compared with a fixed schedule, is up to 40% less water. ESTRON is made in Türkiye; hardware and software are developed locally.

In short: ETc = Kc × ET0. ET0 comes from the weather and is calculated with FAO-56 Penman-Monteith. Kc depends on the plant and the season; 0.80–0.95 for turf. Water to apply = ETc − effective rainfall − water left in the soil. 1 mm = 1 L/m². Duration = water × area ÷ flow.

Frequently asked

What is the difference between ET0 and ETc?

ET0 is the water loss of the reference grass; it depends only on the weather. ETc is the loss of the actual plant: ET0 multiplied by Kc.

Is an on-site weather station required?

No. ESTRON calculates ET0 from the hourly weather forecast. Rain and soil moisture sensors on site confirm the decision; they are optional.

Is Kc fixed?

No. It rises from sowing to mid-season. Other questions are on the FAQ page.