"Does it work with my existing irrigation system?" is the most common question. The answer is yes. The existing irrigation system is the infrastructure; the timer only makes the decision. ESTRON leaves the infrastructure alone and changes the decision.

What stays?

  • Pipes and drip lines. Everything underground stays. There is no digging.
  • Sprinklers and drippers. The irrigation method does not change.
  • Solenoid valves and valve boxes. The valve stays; the unit is fitted next to it.
  • The water source. Mains, well, tank or treated water; it makes no difference.
  • No cables. No cabinet is built, no cable is laid, no electricity supply is needed.

What changes?

TopicTimerSmart irrigation
DecisionCalendar: same days, same durationBy the site, every day, for every line
ControlOn site, at the devicePanel and mobile app
RecordsNoneEvery decision with its reason
FaultsNoticed on siteIn the panel, from flow data
SeasonSchedule changed by handDuration adapts on its own
RainWaters anywayPostponed

Line by line: the timer and ESTRON comparison table. Gains and limits: advantages and limits of a smart irrigation system.

The upgrade step by step

  1. Site survey. The valve count and line layout are recorded. The coil type is checked; the unit works with DC latching solenoids. Three criteria: a DC latching coil, a two-wire coil connection and room in the valve box for the unit.
  2. The existing schedule is noted. The timer's days, time and duration are written down. The first reference duration comes from there.
  3. A version is chosen. On a small single-valve area ESTRON BLE is enough. For remote control and AI decisions, ESTRON BLE-LoRa is chosen.
  4. The gateway is installed. In the BLE-LoRa version one LoRaWAN gateway goes on site: a high, open point with power.
  5. Units are fitted. One battery controller in each valve box; the coil wires connect to the unit and 2 × 9 V batteries go in. Fitting takes minutes.
  6. Panel setup. Areas and lines are entered in the panel. A reference duration and rules are set per line: wind limit, no-watering days, time window.
  7. First week of monitoring. Decisions and the site are watched together. Each line is opened once from the panel; the sprinklers are checked.
  8. Roll-out. Once the pilot area shows results, the other lines are added.

The general installation flow: how is it installed? More on moving up from a timer or a sensor system: upgrading without replacing the system.

A battery controller opens the existing solenoid valve; pipes and sprinklers do not change

What happens to the old timer?

It is taken out of service. The coil wires are removed from the timer and connected to the unit. The unit sits in the valve box, next to the solenoid. For the valve's parts and wiring: what is a solenoid valve and how does it work in irrigation?

Choosing a mode: per line

The upgrade does not have to happen all at once. The mode is chosen separately for each line:

  • Fixed schedule. What the timer did, but from the panel, remotely. A good start for the first week.
  • AI. The duration is calculated every day from the site. Postponed if rain is expected, skipped if the soil is moist. Details: AI irrigation.
  • Monthly percentage. A separate ratio for each month; the seasonal change comes from a table, not by hand.

A newly planted area can stay on a fixed schedule while the mature lawn moves to AI mode. You switch between modes in the panel.

The cost logic

There is no infrastructure item; the pipes, sprinklers and valves are already there. The cost is limited to one unit per valve and one gateway per site. Sensors are optional. The items: smart irrigation system cost. ESTRON is made in Türkiye; hardware and software are developed locally.

In short: the infrastructure stays, the decision changes. The coil type is checked at the survey; the timer's schedule becomes the reference duration. A battery unit in the valve box, one gateway on site. Watch the first week on a fixed schedule, then move to AI line by line.

Frequently asked

Does irrigation stop during the upgrade?

No. A line is off for a few minutes while the unit is fitted. The schedule is loaded straight away; that night the line waters at its usual time.

Do I remove the timer completely?

The coil wires move to the unit; the timer is out of service. It can stay in the box, but it no longer drives the valve.

Is it worth it on a small single-valve area?

On one line the gain is small; a fixed schedule is often enough. The gain grows with the number of lines, how scattered they are and the cost of site visits. Other questions are on the FAQ page.